Tire Size Calculator

The code on a sidewall — 225/65R17 — is a complete specification written in three numbers. Enter any metric tire size and this tire size calculator decodes it: overall diameter, sidewall height, circumference and revolutions per mile, the figures that decide fit, gearing and speedometer truth.







Reading the Sidewall: Width, Ratio, Rim

The metric size code is three measurements in two unit systems, and decoding it is the calculator's first service. 225 is the section width in millimetres — the tire's breadth at its widest. 65 is the aspect ratio: the sidewall's height as a percentage of the width — 65 percent of 225 mm is a 146.25 mm sidewall — the number that separates a tall, cushioned touring tire (70, 65) from a low-profile performance one (40, 35), whose sidewall in millimetres shrinks even as widths grow. R17 is the rim diameter in inches (the R announces radial construction), the code's imperial fossil. The overall diameter — the figure everything else derives from — is the rim plus two sidewalls: 17 × 25.4 + 2 × 146.25 = 724.3 mm, or 28.52 inches. Every output on this page (circumference, revolutions, speedometer error, gearing effect) is that one sum wearing different clothes, which is why a size change that preserves the diameter preserves the car's behaviour even as width and profile change — the principle behind "plus sizing", taken up below.

Worked Example: 225/65R17, Fully Decoded

The defaults are a common crossover fitment. Sidewall: 225 × 0.65 = 146.25 mm (5.76 inches). Overall diameter: 724.3 mm = 28.52 in. Circumference: π × 724.3 ≈ 2,275 mm — each revolution carries the car 2.28 metres. Revolutions per mile: 1,609,344 mm ÷ 2,275 ≈ 707 — the figure tire makers publish as "revs per mile" and transmission engineers use for gearing and odometer calibration. Two comparisons give the numbers meaning. Switch to the same family's 235/60R17 (a wider, lower-profile alternative): sidewall 141 mm, diameter 713.8 mm — 1.4 percent smaller, a speedometer shift of the same small order, acceptable. Switch instead to 225/65R18 (an inch more rim, same profile numbers): the sidewall stays 146.25 but the rim grows 25.4 mm, and the diameter reaches 749.7 mm — 3.5 percent taller, into the range where speedometer error, clearance and gearing all start arguing. The calculator exists to run these comparisons in numbers before the purchase runs them in sheet metal.

Plus Sizing and the 3 Percent Rule

Changing wheel size without changing overall diameter — plus sizing — is the one modification the arithmetic blesses: up an inch of rim, down the aspect ratio to surrender the same sidewall height, wider if the arches allow, and the diameter (hence gearing, speedometer, ride height and ABS calibration) stands still. The classic sequence for the worked example's car: 225/65R17 → 235/55R18 → 245/45R19 keeps diameters within a few millimetres while the sidewall shrinks and the steering sharpens — the trade being ride comfort, pothole vulnerability and price, all moving the other way. Where the diameter does change, the industry rule of thumb holds overall diameter within ±3 percent of the original: inside it, speedometer error stays modest and clearances usually survive; beyond it, the errors compound into gearing changes (a taller tire is a taller final drive — lazier acceleration, lower cruising rpm), odometer undercounting, and on all-wheel-drive vehicles, driveline wind-up if sizes differ axle to axle. This page's diameter output is the number to hold against the rule, and its note states the speedometer consequence plainly enough to quote at a tire counter.

Revolutions, Gearing and the Speedometer's Honesty

The revolutions-per-mile figure is where tire arithmetic meets the drivetrain. The speedometer and odometer do not measure speed or distance; they count rotations and multiply by the circumference the car was calibrated with — so any diameter change falsifies both instruments by the same percentage, in the same direction: taller tire, fewer revolutions per true mile, instruments reading low (you are going faster and farther than shown — the direction that earns tickets and under-records warranty miles). The calculator's percentage is the correction factor for mental arithmetic en route. Gearing feels the same ratio: a 3 percent taller tire raises every gear's effective ratio by 3 percent, which drivers experience as slightly lazier pickup and slightly calmer motorway cruising. And the spare tire question belongs here too: a compact spare's smaller diameter is why its speed and distance limits exist — its revolutions per mile diverge enough to confuse differential and stability systems, a mismatch this page will quantify for any two sizes you enter.

The Rest of the Sidewall: Load Index and Speed Symbol

After the size, the sidewall prints two more codes that complete the tire's legal identity, and a size calculator's readers are usually mid-purchase, where they matter. The load index is a number from a standard table — the common fitment's 102 means 850 kg per tire — and a replacement must meet or exceed the original's, since four tires times the index is the vehicle's rated carrying ceiling. The speed symbol is a letter from its own table — H is 210 km/h (130 mph), T is 190, V is 240 — certifying the tire's sustained-speed capability under load; fitting a lower symbol than the car's specification is both an insurance and a safety problem even for drivers who never approach the speed. Neither code changes the geometry this page computes, but both constrain which tires the geometry may be shopped among — the full sidewall reading is: size (this page), capacity (the index), capability (the symbol), and the manufacturing date code beside them, the four-figure week-and-year stamp that tells a buyer the tire's true age before its first mile — rubber ages on the shelf as surely as on the road, and the stamp is the only honest witness either place.

Related Tools

More from the Everyday Life Calculators hub: the Drive Time Calculator — what the decoded tires will be doing — the Gas Calculator (a diameter change moves real fuel economy too), and the Height Converter for the imperial-metric translations this page's code is built from.

Frequently Asked Questions

What does 225/65R17 mean, in one sentence?

A radial tire 225 millimetres wide whose sidewall height is 65 percent of that width (146.25 mm), fitted to a 17-inch rim — overall diameter 28.52 inches, as the worked example computes. The letters around the numbers add duty ratings (P for passenger, LT for light truck) and the separate speed and load indices printed after the size; the geometry, which is this page's subject, is fully carried by the three numbers and the R.

Can I replace my tires with a different size?

Within the diameter discipline of the article: yes, sizes holding overall diameter within about ±3 percent, with widths the rim and arches accept, and load and speed ratings at least equal to the original. The calculator verifies the diameter condition for any candidate; a tire professional verifies the rest (rim width range, clearance at full lock and compression, rating sufficiency). All four corners should match, and on all-wheel-drive vehicles the tolerance across axles is tighter still — the same diameter, in practice, not merely a similar one.

Why does a bigger rim not always mean a bigger tire?

Because the tire's overall diameter is rim plus sidewalls, and plus sizing trades one against the other: a 19-inch rim wearing a 45-profile tire can stand exactly as tall as a 17-inch rim in 65-profile — the worked example's family demonstrates both ends of the trade. Overall diameter is the conserved quantity, not rim size; judging a fitment by the rim number alone is the novice error this page's first calculation exists to prevent.

How much does a wrong size change my speedometer?

By the diameter ratio, exactly: indicated speed is true speed multiplied by (old diameter ÷ new diameter). Fit a tire 3.5 percent taller — the R18 example in the article — and an indicated 60 is a true 62.1, with the odometer under-recording every mile by the same 3.5 percent. The calculator's note performs the small version of this warning on every decode; for a specific swap, divide the two diameters it reports and the percentage error is yours to two decimal places.

What is a 31-inch off-road tire in metric size?

About 265/75R15: the flotation sizing used off-road (31×10.50R15 — diameter × width × rim, all inches) translates to a metric tire of diameter 15 × 25.4 + 2 × (265 × 0.75) = 778.5 mm ≈ 30.65 inches — sold as a 31 because flotation sizes are nominal to the nearest inch. Enter 265, 75 and 15 in this calculator and it returns the metric tire's true geometry; the exercise matters because the two sizing dialects share showrooms, and a "31-inch" tire and a 265/75R15 are the same object described by rival conventions, within a manufacturer's tolerance of each other.

What are revolutions per mile used for?

Gearing and calibration, chiefly: transmission and final-drive selection multiply engine rpm down to wheel rpm, and revs per mile is the wheel-side figure that closes the calculation (it sets cruising rpm, speedometer drive ratios and odometer counts). Tire manufacturers publish it per model because the same nominal size varies by millimetres between brands — the measured revs of two "identical" sizes can differ by a percent — which is the professional's reminder that this page computes the size's geometry, while a specific tire's data sheet has the last word.