dBm to Watts Calculator
Radio power is quoted in dBm — decibels measured against one milliwatt — and intuition is quoted in watts. Enter a value either way and this dBm to watts calculator converts between dBm, watts and milliwatts instantly, in both directions.
What a dBm Is: A Watt in Logarithmic Clothing
The decibel is a ratio; the dBm pins that ratio to a reference — one milliwatt — turning it into an absolute power: dBm = 10 × log₁₀(power ÷ 1 mW). The logarithm is not decoration. Radio signals span an absurd range — a Wi-Fi router transmitting 100 mW (20 dBm) delivers perhaps a ten-billionth of that to a laptop across the room (about −70 dBm) — and only a log scale lets one column of figures hold both ends of that journey, with losses and gains along the way (cable: −3 dB, amplifier: +20 dB, antenna: +6 dBi) adding and subtracting like a ledger instead of multiplying into exponents. Inverting the formula is this page's whole arithmetic: watts = 10^((dBm − 30) ÷ 10), the 30 appearing because a watt is a thousand milliwatts and 10 × log₁₀(1000) = 30. Every conversion the calculator performs is that one line, and every anchor the note lists is the line evaluated at a round number: 0 dBm = 1 mW by definition, 10 dBm = 10 mW, 20 = 100 mW, 30 dBm = 1 W, 40 = 10 W, 50 = 100 W.
Worked Examples: Transmitters, Routers and Whisper Signals
The default, 30 dBm = 1 watt, is the reference transmitter — the order of a handheld radio's full shout. Down the scale: a typical Wi-Fi access point at 20 dBm is 100 mW; a Bluetooth radio at 10 dBm is 10 mW; a mobile phone at its maximum, around 23–24 dBm, is about 200–250 mW, and it spends most of its life far below that, throttled by the network. The negative country is where signals are received: −30 dBm is a microwatt (0.001 mW), a strong local signal; −70 dBm is 100 picowatts, a good Wi-Fi reading; −90 dBm is a picowatt — 0.000000001 mW — near the edge of usability; and thermal noise itself, the floor of the universe at room temperature, sits near −174 dBm per hertz of bandwidth, the number radio engineers budget against (the ITU's radio-noise recommendations are the formal reference). A converter that prints milliwatts to six decimals, as this one does, still cannot sensibly print −90 dBm's wattage in decimals — 0.000000000001 W — which is rather the point of the dBm: it keeps the whole range speakable.
The Two Rules That Replace the Calculator in the Field
Practitioners carry two approximations that cover most mental conversions, and this page's answers can be checked against them. The 10 dB rule is exact: +10 dB multiplies power by exactly ten, −10 divides by ten — so the decades of the anchor list (0, 10, 20, 30 dBm) are exact milestones, each ten times the last. The 3 dB rule is nearly exact: +3 dB doubles power — precisely ×1.995, an error of a quarter of a percent — and −3 dB halves it, the famous "half-power point" of filter and antenna specifications. Between the two rules every value is reachable: 23 dBm is 20 + 3, hence 100 mW doubled, 200 mW (the calculator: 199.5); 37 dBm is 30 + 10 − 3, hence 1 W × 10 ÷ 2 = 5 W (the calculator: 5.01). Link budgets — the accounting that decides whether a signal path closes — are done in these additions all the way from transmitter dBm to receiver dBm, with distance, cables and weather each taking their dB cut, and the watt is consulted only at the ends, which is to say, on pages like this one.
dBm's Relatives: dB, dBW, dBi and the Family Resemblances
The suffix after dB always names the reference, and confusing the family members is the field's standing error. dB alone is a pure ratio (a gain or a loss) with no absolute meaning. dBm references a milliwatt, dBW a watt — the same power is 30 lower in dBW than in dBm (our 1 W default is 30 dBm and 0 dBW), and satellite and broadcast engineering, working in whole watts, often prefers dBW. dBi is not a power at all but an antenna's gain over the theoretical isotropic radiator — it enters link budgets as an addition to a dBm figure, never a conversion of one. dBmV and dBµV reference voltages (in cable and receiver work, across a stated impedance — usually 75 or 50 Ω), and crossing between voltage-dB and power-dBm requires the impedance, a conversion of a different species. The calculator holds to the power pair (dBm ↔ W, with mW alongside) and names the family so that a value found in a datasheet can be identified before it is converted — most "wrong" conversions in RF work are right arithmetic performed on the wrong relative.
Measuring What You Converted: Instruments and Their Floors
A conversion is only as true as the measurement behind it, and RF power measurement has its own honest limits worth a paragraph. Dedicated power meters and spectrum analysers read dBm directly with accuracies of a few tenths of a dB; oscilloscopes measure voltage, from which power follows only through the impedance (in a 50 Ω system, watts = V² ÷ 50 — a conversion through Ohm's law that this page's family section foreshadows). A ±0.5 dB measurement uncertainty is a ±12 percent power uncertainty — the log scale's compression cuts both ways, flattering big ranges and forgiving small errors — which is why specifications quote dB tolerances and why a calculated 200 mW that measures 180 mW is agreement, not discrepancy. The calculator converts exactly; the bench measures approximately; engineering is knowing which of the two your current question needs.
Related Tools
More calculators live on the Other Calculators hub and among this site's physics tools: the VSWR Calculator — the antenna mismatch that eats the watts this page counts — the Battery Life Calculator for the power source at the other end of the radio, and the LM317 Calculator for the regulator in its power supply.
Frequently Asked Questions
How many watts is 20 dBm?
0.1 watt — 100 milliwatts exactly. Twenty is two decades above the 0 dBm milliwatt, so two factors of ten: 1 mW → 10 mW → 100 mW. The figure is the classic Wi-Fi transmit power and a good anchor to memorise alongside the others this page lists: 10 dBm = 10 mW, 20 = 100 mW, 30 = 1 W, each step a clean tenfold, with the +3 dB doubling rule filling the gaps between the round numbers (23 dBm ≈ 200 mW).
Can dBm be negative?
Yes — negative dBm simply means less than a milliwatt, and nearly every received signal lives below zero: −50 dBm is 10 nanowatts, −100 dBm is a tenth of a picowatt, and sensitive receivers work meaningfully at −120 dBm. The scale has no floor at zero power in the practical sense — zero watts itself would be minus infinity dBm, which is why the calculator's reverse direction refuses 0 W with the note it shows. Negative decibels frighten newcomers only until the first received signal is converted.
What is the difference between dBm and dB?
A reference. dB compares two powers ("the amplifier adds 20 dB"); dBm states one power absolutely, against a milliwatt ("the amplifier outputs 20 dBm"). The two combine arithmetically — a 0 dBm source through a 20 dB amplifier gives 20 dBm out; two dBm figures subtract to a dB ratio — and the discipline of keeping them straight is the whole grammar of link budgets. A value quoted as plain "dB" where a power is meant is a datasheet error worth catching, and this page's family section is the field guide to catching it.
How do I convert dBm to dBW?
Subtract 30: dBW = dBm − 30, because the references differ by a factor of a thousand (30 dB). So 30 dBm = 0 dBW, 50 dBm = 20 dBW, and a satellite transponder's 13 dBW is 43 dBm. The watt figure, of course, is identical either way — the conversion this page performs lands on watts, from which both dialects can be read, since watts are the substance the two notations merely label.
What is 100 watts in dBm?
50 dBm — five decades above the milliwatt, read off the anchor chain (10 is 10 mW, 20 is 100 mW, 30 is 1 W, 40 is 10 W, 50 is 100 W) and confirmable in the reverse direction of this calculator. The figure is a working anchor for the amateur radio and broadcast world, where 100 W is a standard transmitter class; the next decade up, 60 dBm, is a kilowatt, the territory of serious broadcast and the legal ceiling of amateur power in many jurisdictions (1,500 W there is 61.8 dBm).
Why do receivers quote sensitivity in dBm?
Because sensitivity is a power so small that watts would drown it in zeros: "−174 dBm plus the noise figure" compresses the physics (thermal noise density at room temperature, the fundamental floor) into arithmetic a designer can budget — add antenna gain, subtract cable and path losses, compare against the required signal-to-noise. The dBm lets a whole radio path be planned in additions on one line of a notebook; this converter exists for the moments when the plan must be translated back into the watts a power supply, a regulator or a licence actually specifies.